Nov 28, 2025 Leave a message

Key Points And Compliance Checklist For Gasoline Tricycles

I. Standard Application and Name Clarification

• In my country's technical regulatory system, compliance for gasoline tricycles is typically regulated under the category of "three-wheeled vehicles." The mandatory national standard GB 18320-2025, "Safety Technical Specifications for Three-Wheeled Vehicles," has been released and is scheduled to take effect on November 1, 2026, fully replacing GB 18320-2008 and GB 24943-2010. This standard clarifies that a three-wheeled vehicle is "a freight vehicle with a maximum design speed of less than or equal to 50 km/h and three wheels," applicable to the entire chain of design, manufacturing, and inspection. The clarification of terminology and boundaries helps enterprises and inspection agencies to unify their judgments and avoid compliance deviations caused by confusion between "low-speed trucks/three-wheeled vehicles/motorcycles."

 

II. Core Technology Requirements Framework

• Vehicle and Structural Safety: Requirements are proposed for vehicle regularity, power-to-weight ratio not less than 4.0 kW/t, mass utilization coefficient category limits, tank truck baffle and capacity matching formula, vehicle exterior and prohibition of mirror reflections/outward expansion structures, covering structural strength and passive safety baselines.

• Cab and Handling Safety: Quantitative indicators are proposed for the following: rear space of ≥200 mm in the extended cab, width and depth of the main seat ≥400 mm each, passenger seat cushion width ≥350 mm/depth ≥300 mm, and clearance and degrees of freedom of the control mechanism, taking into account ergonomics and prevention of misoperation.

• Steering, Braking, and Driving: The maximum free rotation of the steering wheel, torque capacity of the steering limit device, hydraulic/pneumatic braking system and response time testing, tire specifications/tread/wheel runout, speed limiters and prohibition of overspeed gears, etc., systematically constraining dynamic safety performance.

• Lighting, Signaling, and Visibility: Strengthens requirements on headlight beam position, total high beam intensity, signal device light distribution, retroreflectors, rearview mirror performance and installation angle, and prohibition of external obstructions. Improves the standardization requirements for safety signs and usage information.

 

 

III. Supporting and Specialized Standards

• General Technical Conditions: GB/T 24945-2021 "General Technical Conditions for Three-Wheeled Vehicles" systematically specifies requirements for model designation, control mechanism return, seat dimensions, wheel tumble, generator/battery, headlight low beam position, overall dimensions/axle load/mass, braking performance, and test methods. It also adds technical and inspection requirements for electric three-wheeled vehicles, serving as crucial support for engineering design and consistency control.

• Fuel System Safety: The current version of GB/T 21423, "Safety Performance Requirements and Test Methods for Fuel Tanks of Three-Wheeled Vehicles," is the 2008 version, which is included in the revision plan (GB/T 21423-2025). This standard specifies the safety performance and verification methods for the fuel tank body and its installation. Enterprises are advised to conduct design and verification in advance according to the new version's technical requirements.

• Noise and Emission Methodology: The general technical conditions reference GB/T 19118 (Noise Measurement) and GB 19757 (Limits and Measurement Methods for Exterior Noise During Acceleration). For emissions and energy consumption, GB 20891 (Non-Road Diesel Engine Emissions) and GB 21377 (Limits and Measurement Methods for Fuel Consumption of Three-Wheeled Vehicles) are referenced, forming a "method-limit" matching chain, facilitating type testing and consistency maintenance.

 

IV. Key Points and Judgment Methods for Compliance Implementation

• Standard Validity and Switchover: During product development and type testing, it is recommended to align technical requirements and test methods with GB 18320-2025 in advance to ensure technical convergence and certification preparation are completed before the switchover deadline of November 1, 2026, avoiding repeated testing and cycle risks caused by standard switchover.

• Key Tests and Documentation: Configure testing capabilities around mandatory clauses, focusing on braking response time (Appendix B), lighting/signal light distribution, control clearance and torque, seat dimensions, VIN/labels/instruction manuals, etc.; simultaneously improve test reports, inspection records, usage information, and safety sign drafts to ensure traceability and consistency.

• Scenario-Specific Supplementary Clauses: For applications such as tank transport, self-unloading devices, and complex road conditions/heavy loads, in addition to meeting general clauses, special requirements such as baffles, roll stability angle, speed limiters, and structural strength should be carefully checked to ensure that the actual safety boundary is not lower than the standard lower limit.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry